View SP8908MP_351142.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SP8908 (MP)
5GHZ / 8 Fixed Modulus Divider Preliminary Information
DS4359 ISSUE 1.3 September 1999
The SP8908 is one of a range of very high speed low power prescalers for professional applications. The dividing elements are static D type flip flops and therefore allow operation down to DC if the drive signal is a pulse waveform with fast risetime. The output stage has a differential current output and provides a direct drive into a 50 ohm load.
Ordering Information
SP8908/KG/MP1S (tubes) SP8908/KG/MP1T (tape and reel)
Features
* Very High Operating Speed * Operation down to DC with Square Wave Input * Silicon Technology for Low Phase Noise (Typically better than 2140dBc/Hz at 1KHz) * 5V Single Supply Operation * Low Power Dissipation: 360mW (Typ.) * Surface Mount Plastic Package
Absolute Maximum Ratings
Supply voltage, VCC 6*5V Storage temperature 265C to 1150C Maximum junction temperature 1150C Prescaler input voltage 2*5Vp-p Operating temperature KG240C to 185C TCASE
OUTPUT VCC VCC
1 8 7 6
48
OUTPUT OUTPUT
VREF
400 INPUT INPUT
2 3
400 10mA
4
4
GND
Figure 1 - Block Diagram
SP8908
Preliminary Information
VCC INPUT INPUT GND
1 2
8 7
OUTPUT VCC OUTPUT OUTPUT GND
SP8908
3 4
6 5
MP8
Figure 2 - Pin connections - top view
Electrical Characteristics
These characteristics are guaranteed by either production test or design over the following range of operating conditions unless otherwise stated: TAMB = 240C to 185C, VCC = 4*75V to 5*25V Value Characteristic Supply current Input frequency Input sensitivity Input sensitivity Input overload Input overload Output voltage Output power Pin 1, 8 2, 3 2, 3 2, 3 2, 3 2, 3 6, 7 6, 7 Min. 1*0 440 700 210*0 Typ. 72 0*5 0 Max. 96 5*0 180 570 12*0 Units mA GHz mVrms mVrms mVrms mVrms Vp-p dBm Conditions
RMS sinewave fIN = 1GHz and 4.2GHz fIN = 5GHz fIN = 1GHz and 3GHz fIN = 5.0GHz and 3.8GHz Into 50 pullup resistor fIN = 1GHz and 5GHz (see note 1 )
NOTE 1. Measured into 50 measuring instrument in parallel with 50 pullup resistor. See Figure 5.
800
VIN INTO 50 (mV RMS)
600
TESTED AS PER TABLE OF ELECTRICAL CHARACTERISTICS
400 OPERATING WINDOW 200
1
2
3
4
5
6
7
FREQUENCY (GHz)
Figure 3 - Typical input sensitiviy (sinewave drive)
2
Preliminary Information
SP8908
VCC 15V
1
8
50
50
SIGNAL GENERATOR
1n
2 3
1n
SP8908
7 6 1n 5 10n
50 MEASURING INSTRUMENT
10n
1n
4
Figure 4 - Typical application and test circuit
j1 j0.5 3GHz j0.2 5GHz j5 j2
0
0.2
0.5
1
2
5 0*3GHz 2j5
1GHz 2j0.2
2j0.5 2j1
2j2
Figure 5 - Typical input impedance
3
L(f) [dBc/Hz]
4 100 1k FREQUENCY (Hz) 10k 100k
SP8908
0
2 10
2 20
2 30
2 40
2 50
2 60
Preliminary Information
2 70
2 80
2 90
2 100
2 110
2 120
2 130
2 140
2 150
Figure 6 - Typical phase noise, input frequency = 3GHz
2 160
2 170
10
For more information about all Zarlink products visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. trading as Zarlink Semiconductor or its subsidiaries (collectively "Zarlink") is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink's conditions of sale which are available on request.
Purchase of Zarlink's I2C components conveys a licence under the Philips I2C Patent rights to use these components in an I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 2002, Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE

▲Up To Search▲

Price & Availability of SP8908MP

	To Download SP8908MP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .